30W 高压电源
EPM 系列高压电源是一个高效、紧凑的设计，提供了非常好的调节、低纹波高压。
输出电压和电流在全操作范围是可控的。电压和电流编程和监测信号都是0-10Vdc 对应0 至100% 额定输出。一个高压禁用/启用信号允许简单的开/关电源的控制。
典型应用:
- 电泳
- 电子束
- 离子源
- 光电倍增管
- 实验应用
- 静电纺丝
规格
(Ref. 128003-001 REV. P)
Input:
+24Vdc ±10% @ 2A
Output:
8 models from 1kV to 30kV. Each model is available in positive or negative polarity output.
Voltage Regulation:
Load: 0.02% of output voltage for a full load change.
Line: 0.01% for ±10% change in input voltage.
Current Regulation:
Load: 0.01% of output current from 0 to rated voltage.
Line: 0.01% of rated current over specified input range.
Ripple:
0.1% p-p of maximum rated output voltage.
Dimensions:
2.06”H x 5.63”W x 5.69”D
(52.32mm x 143mm x 144.53mm)
Weight:
2.2 pounds (1kg)
Input Connector:
9 pin AMP Metri-Mate. Mating connector and pins supplied.
Output Cable:
18” ±1” (457mm) of UL® listed high voltage wire.
Voltage Stability:
0.02% per 8 hours (after 1/2 hour warm-up).
Voltage Temperature Coefficient:
0.01% per °C.
Voltage Test Point:
10Vdc ±2% = maximum rated output.
Current Test Point:
10Vdc ±2% = maximum rated output.
Remote Enable:
3.4Vdc = HV ON.
1.0Vdc or open = HV OFF.
Regulatory Approvals:
Compliant to EEC EMC Directive (1kV to 15kV only).
Compliant to EEC Low Voltage Directive (1kV to 15kV only).
UL/CUL recognized, File E148969 (1kV to 15kV only).
EPM SELECTION TABLE
| Maximum Rating | Model Number | |
|---|---|---|
| kV | mA | |
| 1 | 30 | EPM 1*30 |
| 3 | 10 | EPM 3*30 |
| 5 | 6 | EPM 5*30 |
| 10 | 3 | EPM 10*30 |
| 15 | 2 | EPM 15*30 |
| 20 | 1.5 | EPM 20*30 |
| 25 | 1.2 | EPM 25*30 |
| 30 | 1 | EPM 30*30 |
*Specify “P” for positive polarity or “N” for negative polarity.
INPUT— 9 PIN AMP CONNECTOR
| Pin | Signal | Parameters |
|---|---|---|
| 1 | Power Ground | Power Ground |
| 2 | +24Vdc | +24Vdc @ 1.85 amps, maximum |
| 3 | High Voltage Enable/Inhibit | 0Vdc = HV OFF, +5Vdc = HV ON (see manual for details) |
| 4 | Voltage Test Point | 0 to 10Vdc = 0 to 100% rated output, Zout = 10kΩ |
| 5 | Current Test Point | 0 to 10Vdc = 0 to 100% rated output, Zout = 10kΩ |
| 6 | Voltage Programming | 0 to 10Vdc = 0 to 100% rated output, Zin = 10MΩ |
| 7 | Current Programming | 0 to 10Vdc = 0 to 100% rated output, Zin = 10MΩ |
| 8 | +10Vdc Reference | +10Vdc @ 1mA maximum |
| 9 | Signal Ground | Signal Ground |
表和图
DIMENSIONS: in.[mm]
SIDE VIEW
TOP VIEW
FRONT VIEW
Frequently Asked Questions
What Is a Safe Level of High Voltage?
Where Can I Obtain Information on High Voltage Safety Practices?
What Kind of High Voltage Connector Do You Use on Your Supplies?
What Do You Mean That the Output Side of the High Voltage Cable on Most Standard Products Is “Unterminated”?
How Should I Ground Your Supply?
Why Is Arcing an Issue for a High Voltage Power Supply?
