XRB101 Monoblock® X射线发生器 (featured)

XRB150PN600 Monoblock® X射线发生器

  • 集成高压电源,灯丝电源,X 射线管,电子束端口和控制电子设备
  • 紧凑,轻便
  • 功率因数校正
  • 可以安装在任何物理方向
  • 模拟监控和标准 RS-232 数字接口

*注意:所有规格如有变更,恕不另行通知。有关最新修订,请参阅本数据表的英文 PDF 版本

150kV,600W X 射线源

  斯派曼 XRB150PN600 系列 Monoblock® X 射线源专为 OEM 应用而设计。输出电压为 150kV,功率为 160W,为内部 X 射线管供电。产品具有通用输入,小的外观尺寸,标准的模拟接口和RS-232 数字接口等特点,使得此 Monoblock® 能更简单集成到 X 射线系统中。标准的型号提供锥形射线束。专有的发射控制电路提供了卓越的 X 射线管电流管理,同时具有出色的稳定性能。

  • X 射线扫描:骨密度测量
  • 食品检验
  • 安全

规格

(Ref. 128079-001 REV. G)

X-Ray Characteristics:

Tube Type:  Glass tube, Tungsten target, Be filter

Focal Spot:  0.5mm x 0.5mm (IEC 336)

Beam Filter:  0.06. Ultem

Beam Geometry:  Cone up to 18° ±1°

Input Voltage:

Vac, 50/60Hz, 6.5A maximum 200-240 +/-10% 

X-Ray Tube Voltage:

Nominal X-Ray tube voltage is adjustable between 70kV to 150kV

X-Ray Tube Current:

1.0mA to 4.0mA over specified tube voltage range

X-Ray Tube Power:

160W continuous, 600W peak Duty Cycle: 30 seconds on, 300 seconds off @ 600W peak

Voltage Regulation:

Line: ±0.1% for a ±10% input line change of 180 to 264Vac

Load: ±0.1% for a 1.0mA to 4.0mA load change. 600W maximum

Voltage Accuracy:

Voltage measured across the X-Ray tube is within ±2% of the programmed value

Voltage Risetime:

±1% in less than 300ms

Voltage Overshoot:

±10% during 300ms risetime

Voltage Ripple:

1% rms of rated voltage @ 10Hz to 1MHz

Current Regulation:

Line: ±0.1% from 180-264Vac

Load: ±0.5% @ 70-150kV, 1.0mA to 4.0mA

Current Accuracy:

Current measured through the X-Ray tube is within ±2% of the programmed value

Current Risetime:

±1% in less than 300ms

Arc Intervention:

4 arcs in 10 seconds with a 200ms quench = Shutdown

Filament Configuration:

Internal high frequency AC filament drive with closed loop filament emission control

Analog Interface:

0 to 5Vdc ground referenced signals

Digital Interface:

RS-232 interface.

Control Software:

A demo GUI for engineering evaluations will be provided for the RS-232 digital interface upon request.

Interlock/Signals:

A hardware interlock function is provided

Operating Temperature:

0°C to +40°C

Storage Temperature:

-40°C to +70°C

Humidity:

10% to 95% relative humidity, non-condensing

Cooling:

External fan required. 250cfm minimum to maintain an oil temperature of 55C° or less.

Input Line Connector:

3 pin Phoenix Contact P/N 1829167

Analog Interface Connector:

10 pin Phoenix Contact P/N 1755503

Digital Interface Connector:

9 pin D connector, female

Grounding Point:

8-32 ground stud provided on chassis

Dimensions:

13.46" X 13.38" X 6.24"
(341.89mm X 339.85mm X 158.50mm)

Weight:

66lbs (30kg)

Orientation:

Can be mounted in any orientation.

X-Ray Leakage:

Less than 100mR/hr at 1m distance, measured at 140kV, 3mA.

AC INPUT POWER JB1 3 PIN PHOENIX CONTACT

Pin Signal Parameters
1 Line 180-264Vac
2 GND Chassis Ground
3 Neutral Neutral

 RS-232 DIGITAL INTERFACE— JB16 9 PIN FEMALE D CONNECTOR

Pin Signal Parameters
1 Spare N/C
2 Transmit RS-232
3 Receive RS-232
4 Spare N/C
5 Signal Ground Ground
6 Spare N/C
7 Spare N/C
8 Spare N/C
9 Spare N/C

ANALOG INTERFACE— JB15 10 PIN PHOENIX CONTACT

Pin Signal Parameters
1 X-Ray Signal +12Vdc =Enable X-Ray, 0Vdc/open = Disable X-Ray, Zin=1kΩ
2 X-Ray Signal Return Signal Return
3 N/C N/C
4 kV Monitor 0 to 5Vdc = 0 to 175kV, Zout= 10kΩ
5 Signal Ground Signal Ground
6 mA Monitor 0 to 5Vdc = 0 to 4.5mA, Zout= 10k
7 Fault Signal Open collector, High (Open) = No Fault, 35Vdc @10mA maximum
8 HV ON Lamp Relay n/o Relay Normally Open, 50Vdc @ 1A maximum
9 HV ON Lamp Relay common Relay Common, 50Vdc @ 1A maximum
10 HV ON Lamp Relay n/c Relay Normally Closed, 50Vdc @ 1A maximu

LED INDICATORS

Indicator Signal Name Condition Illuminated When...
LED 1 OT Over temperature occurs
LED 2 ARC FLT Arc fault occurs
LED 3 UV Low kV occurs
LED 4 OV High kV occurs
LED 5 UC Low mA occurs
LED 6 OC High mA occurs
LED 7 X-RAY ON X-Rays are enabled
LED 8 PWR Power is ON

表和图

DIMENSIONS: in.[mm]

FRONT VIEW TANK

XRB101 Monoblock® X射线发生器 (Image 2)

SIDE VIEW TANK

XRB101 Monoblock® X射线发生器 (Image 4)

TOP VIEW TANK

XRB101 Monoblock® X射线发生器 (Image 6)

FRONT VIEW

CONTROL ASSEMBLY

XRB101 Monoblock® X射线发生器 (Image 3)

SIDE VIEW

CONTROL ASSEMBLY

XRB101 Monoblock® X射线发生器 (Image 5)

SIDE VIEW 

CONTROL ASSEMBLY

XRB101 Monoblock® X射线发生器 (Image 7)

Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.



FAQ

为什么使用油绝缘?
我是否需要确保 MONOBLOCK® 保持冷态?为什么?
我多久需要调校一次 MONOBLOCK® X 射线源?为什么?
AN-12 | 动力X射线管灯丝电路使用电流源的益处