XRV 系列 1.8 - 6kW 工业X射线发生器 (featured)

XRV 系列

  • 提供 160kV、225kV、320kV、350kV 和 450kV 型号
  • 完备的 X 射线发生器套件
  • 功率因数校正交流输入电路
  • 集成式双灯丝电源
  • 数字接口 - USB、以太网和 RS-232
  • 高度稳定,合理调节
  • 黑色粉末涂层表面处理

 两年延保标志 CE RU 标识 RoHs 合规标志

*注意:所有规格如有变更,恕不另行通知。有关最新修订,请参阅本数据表的英文 PDF 版本

 

 

配置您的 XRV 子系统

NFC-74-100 认证文件

1.8 - 6kW 工业级 X 射线发生器

斯派曼XRV 系列X 射线高压电源为紧凑型1.8kW 至6.0kW,为高性能X 射线检查发生器树立标准。输出电压范围为160kV至450kV,有负极性、正极性或双极输出配置,这款型号几乎可用于各种应用需求。

有源的功率因数校正电路降低了输入电流的需求,同时将线路相关的EMI 减到最少。斯派曼专有的逆变器拓扑技术可以实现前所未有的效率和功率密度。固态封装高压部分进一步减少了电源的体积和重量,并提供了可靠的、免维护运行。

DSP 基于SMT 控制电路,USB、以太网和RS-232 连同模拟接口供您选择,简化了OEM 系统的集成。两路直流输出、通过复杂的发射电流调节电路控制调节灯丝电源,来提供精确的和稳定的X 射线管电流。全面的故障诊断电路、电弧感应、电弧灭弧和电弧计数功能都成为紧凑的/节省空间的X 射线发生器的一部分。

规格

(Ref. 128060-001 REV. AD)

Typical Applications

Non Destructive Testing
X-Ray Scanning
Security Applications
Medical Applications

Options

400Vac ±10% (6kW only)
GUI Control Software for XRV
XRVC (XRV Controller)

Specifications

Input Voltage:

1.8kW, 3.0kW, 4.0kW and 4.5kW models:

180-264Vac, single phase, 47-63 Hertz, active power factor corrected input to ≥0.98

6.0kW models: 

208 or 400Vac, ±10%, three phase, 47-63 Hertz, passive power factor corrected

Input Current:

1.8kW, 3.0kW, 4.0kW and 4.5kW models: <30 amps

6.0kW models: <25 amps per phase 

Output Voltage:

Accuracy: 0.25%

Stability: ≤ 0.1% per 8 hours, after 1 hour warm up

1.8kW, 3.0kW, 4.0kW and 4.5kW models:

Load:±0.05% of rated output voltage for a full load change

Line: ±0.05% of rated output voltage over specified input voltage range

6.0kW models:

Load:±0.1% of rated output voltage for a full load change

Line: ±0.1% of rated output voltage over specified input voltage range

Output Polarity:

See “model selection” table

Output Current:

See “model selection” table

Ripple: 

See “model selection” table

Temperature Coefficient:

1.8kW, 3.0kW, 4.0kW and 4.5kW models:

50ppm/°C

6.0kW models:

±50ppm/°C

Emission Current:

Accuracy: 0.25%

Stability: 100ppm/°C

1.8kW, 3.0kW, 4.0kW and 4.5kW models:

Load: ±0.05% of rated output current for a change from 30% to 100% of rated output voltage

Line: ±0.05% of rated output current over specified input voltage range

6.0kW models: 

Load: ±0.1% of rated output current for a change from 30% to 100% of rated output voltage

Line: ±0.1% of rated output current over specified input voltage range

Filament:

Output:

0-6 amps at a compliance of 10Vdc, maximum

Dual Focal Spot:

Small and large, selectable via interface signal

Configuration:

DC filament drive. Closed loop emission control regulates filament setting to provide desired X-Ray tube emission current

Control Interface:

Remote Interface:

Analog, USB, Ethernet and RS-232 are standard

Control Software:

A Windows graphical user interface example is provided.

Environmental

Temperature Range: 0°C to +50°C

-40°C to +85°C

Humidity:

20% to 85% RH, non-condensing

Mains Input Connector:

1.8kW, 3.0kW, 4.0kW and 4.5kW models: 

Type 97-3102A-24-11P

6.0kW models:

Type 97-3102A-24-22P

Interface Connectors:

Digital—Ethernet, RS-232 and USB

Analog—25 pin connector

Output Connector:

See “model selection” table

Cooling:

Forced air

Regulatory Approvals:

Compliant to EEC EMC Directive/Compliant to EEC Low Voltage Directive, all but 6000 watt unit. NFC 74-100 compliant. UL/CUL recognized, File E227588, all but 6000 watt unit. RoHS Compliant.

Options

400Vac ±10% (6kW only)

GUI Control Software for XRV XRVC (XRV Controller)

 

XRV160/320/350 SPECIFICATIONS

  XRV160*1800 XRV160*3000 XRV160*4000 XRV160*6000 XRV320P&N1800 XRV320P&N4500 XRV350P&N4500
DC Output Voltage 5kV to 160kV 5kV to 160kV 5kV to 160kV 5kV to 160kV 5kV to ±160kV 5kV to ±160kV 5kV to ±175kV
Polarity* Pos or Neg Pos or Neg Pos or Neg Pos or Neg Bipolar Bipolar Bipolar
Output Rated Current 0-30mA 0-30mA 0-50mA 0-50mA 0-30mA 0-30mA 0-30mA
Output Power 1.8kW 3.0kW 4.0kW 6.0kW 1.8kW 4.5kW 4.5kW
Ripple/Noise (p-p) <0.025% <0.05%  <0.1% <0.25% <0.025% <0.1% <0.1%
Dimensions 10.09˝ H x 17.16˝ W x 24˝ D (256mm x 436mm x 609mm) 2 x (10.09˝ H x 17.16˝ W x 24˝ D) (256mm x 436mm x 609mm)
Weight 150 lbs. (68kg) 150 lbs. (68kg) 150 lbs. (68kg) 155 lbs. (70.3kg) 300 lbs. (136 kg) 300 lbs. (136 kg) 300 lbs. (136 kg)
Output Connector R24 R24 R24 R24 Two R24 Two R24 Two R24

XRV225/450 SPECIFICATIONS

  XRV225*1800 XRV225*3000 XRV225*4000  XRV225*6000 XRV450P&N1800 XRV450P&N4500
DC Output Voltage 5kV to 225kV 5kV to 225kV 5kV to 225kV  5kV to 225kV 5kV to ±225kV 5kV to ±225kV
Polarity* Pos or Neg Pos or Neg Pos or Neg  Pos or Neg Bipolar Bipolar
Output Rated Current 0-30mA 0-30mA 0-30mA  0-30mA 0-30mA 0-30mA
Output Power 1.8kW 3.0kW 4.0kW  6.0kW 1.8kW 4.5kW
Ripple/Noise (p-p) <0.025% <0.05% <0.1%  <0.25% <0.025% <0.1%
Dimensions 15.90˝ H x 17˝ W x 30.72˝ D (404mm x 432mm x 780mm) 2 x (15.90˝ H x 17˝ W x 30.72˝ D) (404mm x 432mm x 780mm)
Weight 240 lbs. (109kg) 240 lbs. (109kg) 240 lbs. (109kg)   480 lbs. (218 kg) 480 lbs. (218 kg)
Output Connector R28** R28** R28**   Two R28** Two R28**

Units are available in positive output polarity without filament, see model selection table for ordering details. 
*Specify “P” for positive or “N” for negative polarity. 
**Order SHV HV cable flange p/n 407141-024 if using Comet HV cable with R28SL spring loaded plug. 

 
J1 HV CONNECTOR—R24/R28

 

Pin Signal Parameters
C HV Output XRV160 and XRV320—R24 Connector
XRV225 and XRV450—R28 Connector
S Small Filament Output 0 to 6 amps @ 10Vdc
L Large Filament Output 0 to 6 amps @ 10Vdc

J2 ANALOG INTERFACE—25 PIN D CONNECTOR

Pin Signal Parameters
1 Power Supply Fault Low, sum of faults, HVPS detected a fault,
open collector, 50V @ 10mA max
2 mA Program 0 to 10V FS Z in = 10M ohms
3 kV Program 0 to 10V FS Z in = 10M ohms
4 Filament Limit L/S Ref.* 0 to 10V FS Z in = 10M ohms
5 Filament Preheat L/S Ref.* 0 to 10V FS Z in = 10M ohms
6 kV Monitor 0 to 10V FS Z out = 4.99k ohms
7 mA Monitor 0 to 10V FS Z out = 4.99k ohms
8 Filament Current Monitor* 0 to 10V FS Z out = 4.99k ohms
9 Signal Ground Ground
10 X-Ray Enable +24Vdc = X-Ray ON, connect to pin 14 with
dry contact relay
11 Filament ON* Filament ON status, low, filament is ON
open collector 50V, @ 10mA max
12 Interlock 1 Active low, interlock is closed, safe to enable HV
13 Interlock 2 Active low, interlock is closed, safe to enable HV
14 +24Vdc +24Vdc @ 100mA, maximum
15 Filament Enable* Active low, turn filament ON
16 Filament Control* Active low, filament is regulated by ECR (HV must
be ON). Not active, the filament is regulated by the
preheat reference
17 Filament L/S Select Filament selection large or small, low = small spot is selected
18 Filament L/S Confirm Open collector, 50V @ 10mA max
Filament selection confirm, low = small spot is selected
19 HVPS RDY Low = HVPS ready, open collector, 50V @ 10mA max
20 X-Ray ON X-Ray ON status, low = X-Rays are ON
open collector, 50V @ 10mA max
21 Interlock Status Low, interlocks are closed, can enable HV
open collector, 50V @ 10mA max
22 GND Digital ground
23 X-Ray ON Pre-Warn Pre-warning, low, before X-Ray ON
open collector, 50V @ 10mA max
24 Reset Active low, minimum 10mS transition
25 Arc fault Low, arc fault, the HVPS has detected an arc
open collector, 50V @ 10mA max

*Not active on positive models  

MODEL SELECTION TABLE

Model Voltage Power Polarity
XRV160*1800 160kV 1.8kW Pos or Neg
XRV160*3000 160kV 3.0kW Pos or Neg
XRV160*4000 160kV 4.0kW Pos or Neg
XRV160*6000/208V 160kV 6.0kW Pos or Neg
XRV160*6000/400V  160kV  6.0kW  Pos or Neg
XRV225*1800 225kV 1.8kW Pos or Neg
XRV225*3000 225kV 3.0kW Pos or Neg
XRV225*4000 225kV 4.0kW Pos or Neg
XRV225*6000/208V 225kV 6.0kW Pos or Neg
XRV225*6000/400V  225kV 6.0kW Pos or Neg
XRV320P&N1800 ±160kV 1.8kW Bipolar
XRV320P&N4500 ±160kV 4.5kW Bipolar
XRV350P&N4500 ±175kV 4.5kW Bipolar
XRV450P&N1800 ±225kV 1.8kW Bipolar
XRV450P&N4500 ±225kV 4.5kW Bipolar

*Specify “P” for positive or “N” for negative polarity. Positive polarity models do not have
integrated filament power supplies. Contact Spellman for custom output voltage/power models.

RS-232 DIGITAL INTERFACE—J3 9 PIN FEMALE D CONNECTOR

Pin Signal Parameters
1 N/C No Connection
2 TX out Receive Data
3 RX in Transmit Data
4 N/C No Connection
5 SGND Ground
6 N/C No Connection
7 N/C No Connection
8 N/C No Connection
9 N/C No Connection

ETHERNET DIGITAL INTERFACE—J4 8 PIN RJ45 CONNECTOR

Pin Signal Parameters
1 VBUS +5 Vdc
2 D- Data -
3 D+ Data +
4 GND Ground

JB1 MAIN AND AUXILIARY INPUT POWER—TYPE 97-3102A-24-11P (Single Phase Units)

Pin Signal Parameters
A Auxiliary AC Line Power 180-264Vac
B Auxiliary Ground Ground
C Auxiliary AC Neutral Neutral
D Main AC Line Power 180-264Vac
E Main Ground Ground
F Main AC Neutral Neutral

JB1 MAIN AC INPUT POWER—TYPE 97-3102A-24-22P (Three Phase Units)

Pin Signal Parameters
A Line 1 208Vac, ±10%, 50/60Hz @ 25 amps
B Line 2 208Vac, ±10%, 50/60Hz @ 25 amps
C Line 3 208Vac, ±10%, 50/60Hz @ 25 amps
D GND Ground

Note: Use 4 conductor cable or single isolated wires rated no
less that 600Vac, 30 amps (10AWG, minimum)

JB2 AUXILIARY AC INPUT POWER—TYPE 97-3102A-20-3P (Three Phase Units)

Pin Signal Parameters
A Line 1 208Vac, ±10%, 50/60Hz (source 3 phase L1, L2)
B Line 2 208Vac, ±10%, 50/60Hz (source 3 phase L1, L2)
C GND Ground

System Ground: System ground wires (10AWG minimum) to
the ground terminal E1 GND to the power supply using ground
stud M6 X 20MM, with M6 nut.

 

表和图

DIMENSIONS: in.[mm]

XRV160

TOP VIEW

XRV 系列 1.8 - 6kW 工业X射线发生器 (Image 3)

FRONT VIEW

XRV 系列 1.8 - 6kW 工业X射线发生器 (Image 5)

REAR VIEW

XRV 系列 1.8 - 6kW 工业X射线发生器 (Image 7)

XRV225

TOP VIEW

XRV 系列 1.8 - 6kW 工业X射线发生器 (Image 4)

FRONT VIEW

XRV 系列 1.8 - 6kW 工业X射线发生器 (Image 6)

REAR VIEW

XRV 系列 1.8 - 6kW 工业X射线发生器 (Image 8)

Note: All specifications are subject to change without notice. Please consult the PDF version of this datasheet for the most up-to-date revision.